Home > Error Code > Dell Error Code 123

Dell Error Code 123

Contents

Enter system setup (see Entering System Setup), review your computer's configuration information, and ensure that the device you want to test displays in System Setup and is active. If the computer starts normally, continue to install additional memory modules (one at a time) until you have identified a faulty module or reinstalled all modules without error. If you wait too long and the operating system logo appears, continue to wait until you see the Microsoft® Windows® desktop. Power Button Light Codes The diagnostic lights give much more information about the system state, but legacy power light states are also supported in your computer. http://completeprogrammer.net/error-code/dell-error-code.html

If else, replace the motherboard. Pb2 1- Off 2- Off 3- Solid 4- Off - Reserved Reserved Pb3 1- Off 2- Off 3- Solid 4- Solid ACPI S3 Suspend to RAM Windows Standby State. If customer can assist to troubleshoot, narrow down the issue by removing one by one the memory on motherboard to determine which one failed. Power connector not installed properly.

Dell Error Code 123 Optiplex 755

The diagnostic lights are not lit after the computer successfully boots to the operating system. Unplug the computer. Please use the reference tables below. After POST is complete, all four diagnostic lights turn green briefly before turning off to indicate normal operating condition.

Sign In Sign Up Community Back Community Forums Community Standards Staff More Back Blogs Calendar Downloads Gallery Store Online Users Activity Back Activity All Activity My Activity Streams Back Status Updates Abused patience turns to fury.  share Link to post Share on other sites nanowatt nanowatt    Member 1,709 posts Your average public offender Posted October 28, 2014 If that doesn't work If two or more memory modules are installed, remove the modules, then reinstall one module and restart the computer. Dell Optiplex 960 Error Code 123 Note: Please be aware that if your system completes POST without stopping on a particular error code and then gives a black screen, the most likely reason is that you are

The BIOS will turn the LED to this states to indicate it has started fetching op-codes. Remove all peripheral cards from the PCI and PCI-E slots and restart the computer. This test typically takes 1 hour or more and requires you to answer questions periodically. http://www.dell.com/support/article/us/en/19/SLN288786 If there is an error message on the screen identifying a problem with a device (such as the floppy drive or hard drive), check the device to make sure it is

S14 1- Solid 2- Solid 3- Solid 4- Off POV Other post-video activity Indicates routine system activity subsequent to video initialization. Dell Optiplex 760 Error Code 123 change it to none. A possible USB failure has occurred. If two or more memory modules are installed, remove the modules, then reinstall one module and restart the computer.

Dell Error Code 0123

These LEDs do not indicate the problem that caused the POST routine to stop. Contact your technical support to take this further. Dell Error Code 123 Optiplex 755 You can customize the tests you want to run. Dell Error Code 1 2 3 If the problem persists, contact Dell (see Contacting Dell).

A possible floppy or hard drive failure has occurred. news If the computer starts normally, reinstall an additional module. A failure has occurred. The Dell Diagnostics obtains configuration information for all devices from system setup, memory, and various internal tests, and it displays the information in the device list in the left pane of Dell Optiplex 980 Error Code 123

If the problem persists, contact Dell. S10 MEM 3, 7 3 blinks followed by a short pause, 7 blinks, long pause, then repeats Possible memory failure Memory subsystem configuration activity is in progress. Corsair 800D Case and AX1200 Ps X-Fi Titanium Fatal1ty pro PCIe Sound CardDell Studio XPS 1645 Window 7 Pro Forum member since 2003 Like 0 Reply You have posted to a have a peek at these guys Reseat the power cable in the power connector on the back of the computer and the electrical outlet.

If the computer starts normally, continue to install additional memory modules (one at a time) until you have identified a faulty module or reinstalled all modules without error. Dell Error Lights 123 If customer can assist to troubleshoot, narrow down the issue by removing one by one the memory on motherboard to determine which one failed. If the computer starts normally, reinstall an additional module.

If the problem persists, contact Dell.

NOTE: The Dell Diagnostics software works only on Dell computers. If none of the PCI Cards failed, replace the motherboard. If the problem still exists, install a graphics card that you know works and restart the computer. Dell Error Beep Codes DELL.COM > Community > Support Forums > Desktop > General Hardware > XPS 420 error diagnostic light 1 2 3 no boot cant even open BIOS Shop > Home & Home

Ensure that no special memory module/memory connector placement requirements exist (see Memory). Sign In Now Sign in to follow this Followers 0 Go To Topic Listing Troubleshooting Recently Browsing 0 members No registered users viewing this page. Ensure that any power strips being used are plugged into an electrical outlet and are turned on. check my blog Register a new account Sign in Already have an account?

Pb0b 1- Off 2- Off 3- Off 4- Off ACPI S0; Normal Operation System is on with no failures detected. If the computer malfunctions, the sequence of the lights help to identify the problem. EDIT *** If your BIOS is Phoenix, and if the "1 long, 3 short, 1 long" code could be reinterpreted as "1 - 3 -1" (see link below), then your BIOS Sign In   Sign In Remember me Not recommended on shared computers Sign in anonymously Sign In Forgot your password?

Pre – POST Diagnostic LED Patterns State LED Pattern ( 1 2 3 4 ) LED Description Power LED State Assignment State Description Pb0a 1- Off 2- Off 3- Off 4- S0e 1- Off 2- Off 3- Off 4- Off ON Normal Operation, ACPI S0 Power LED Solid Green. Help Describes the test and may indicate requirements for running the test. If nothing works, replace the motherboard, power supply or cabling - - 2, 3 2 blinks followed by a short pause, 3 blinks, long pause, then repeats Bad Motherboard, Memory or

If the problem persists, reinstall the card you removed, then remove a different card and restart the computer. Solid White System is in S0 state. If the LED next to the switch does not illuminate, disconnect all internal and external peripherals, and press and hold the power supply test button.If it illuminates, there could be a If you are seeing an unrecognisable code, one that isn't listed above - then please get in touch with your local support straight away.

Uw feedback is verzonden. Sign in here. What brand is your BIOS ? HomeBuilt SandyBridge P8P67 i7 2600k @ 4.5 ghz 8gigs GSkill Ripjaws.

Continue until you have identified a faulty module or reinstalled all modules without error. Generally this means the motherboard is gone. Memory modules are detected, but a memory power failure has occurred. Flash latest BIOS version.

If the problem persists, contact Dell (see Contacting Dell).