I am trying to figure out what it is wrong with it. at the Dell support site. I would think if the battery was dead you would still be able to POST but all the CMOS data would be lost. you should disconnect the device. http://completeprogrammer.net/error-code/dell-hdd-error-codes.html
All rights reserved. Home Articles Products Forums Search Forums Recent Posts Vendors Resources Search Resources Most Active Authors Members Notable Members Current Visitors Recent Activity 0 0 Guest Your Profile I push gray button top left above keyboard. Replace the system board. In Stock $12.95 Dell Latitude E6400 Replacement Speakers - E6400... $12.95 Dell Latitude E6400 Replacement Speakers - E6400 Eligible for $5.00 1st Class Shipping.
If none of the component failed, replace the motherboard. i bought dell computer desk top, it was used one ,i am trying to instore windows but the computer is asking for a password which i think is on the mother Off Blinking Blinking The modem is preventing the system from completing POST.
If your error code is diffferent than those listed above, please contact Dell technical support. Article ID: SLN155342 Last Date Modified: 10/05/2016 07:33 AM Rate this article Accurate Useful Easy If the computer starts normally, continue to install additional memory modules (one at a time) until you have identified a faulty module or reinstalled all modules without error. If the LED next to the switch does not illuminate, disconnect all internal and external peripherals, and press and hold the power supply test button.If it illuminates, there could be a Dell Error Codes 1 2 3 They both have one prong in the center and it was not forced.
Power Button Light Codes The diagnostic lights give much more information about the system state, but legacy power light states are also supported in your computer. Dell Laptop Blink Codes Make sure the PC is OFF and UNLUGGED and only touch the edges of the RAM sticks when removing and reseating them. Artikel-id: SLN265807 Laatste wijzigingsdatum: 02/09/2016 10:16 AM Beoordeel dit artikel Nauwkeurig Nuttig Eenvoudig te begrijpen Was dit artikel nuttig? Instead the Power Button state now gives a blink and colour shift pattern to indicate where its had a problem.
Start>Programs>Accessories>System Tools>System Restore. Dell Support Error Codes Parts-People.com, INC Privacy | Policies © Copyright 2002-2015 Parts-People.com, Inc. The Battery LED will pause for 3 seconds before the next cycle repeat itself again. Under boot options, select the CD drive as the first boot device.
Error code 0146 MSG:error code 2000-0146 MSG:unit 0:DST log contains previous error(s) thanks in advance if you can help me. http://blog.parts-people.com/2014/07/02/dell-latitude-e6400-led-post-codes-diagnostic-indicators/ Join us on our forums and be sure to subscribe to us for weekly tips and other helpful computer articles. Dell Desktop Blink Codes Use the chart below as a reference for the different LED patterns and the possible system issues they indicate. Dell Error Beep Codes Look at the diagnostic LEDs to determine which state the system is in.
Thanks, Janet Dave June 1, 2014 If this is a genuine Windows DVD then you should be able to tap F12 at boot and then enter the BIOS Setup. have a peek at these guys No CPU present. Power LEDs Off Blinking Amber Solid Amber Solid Green Blinking Green Diagnostics LEDs LED Pattern (1 2 3 4) LED Pattern State Name State Description Suggested Resolution Off Off System POST I came across this guy who seemed to have the same symptoms and fixed it with a battery change. Dell Error Codes 1 3
Note : If you have an OptiPlex AIO (All In One) System. Uw feedback is verzonden. Replace the LCD screen. check over here If the problem persists, possible CMOS battery failure or system board failure. 6 Video BIOS Test Failure Video card/chip failure 7 CPU-cache test failure Processor failure 8 LCD LCD failure Note:
In order to achieve a speedy publication, Quick Tips may represent only partial solutions or work-arounds that are still in development or pending further proof of successfully resolving an issue. Dell Error Code Lights A blinking yellow light means there is likely a problem with the motherboard or the power supply. This is the transition state to POST states. 1- Solid2- Off3- Off4- Off - Reserved 1- Blink2- Off3- Off4- Blink A power failure has been detected on a plug-in component such
Replace the motherboard / system board. OptiPlex audible Beep codes In addition to the various types of diagnostics LEDs, there are a number of audible beep codes across all the models of these systems. Connect with me on: Google+ 36 Comments mark harris July 7, 2010 I MOVED MY DAUGHTER OVER THE WEEKEND.HER COMPUTER WAS RUNNING FINE.SHE PUT IT IN THE TRUNK OF HER CAR.ONE Dell Error Code 2000-0142 Dell Latitude E6400 LED Light Codes LED Light Code Component Causing No POST Possible Solution(s) Motherboard / System Board Fault Replace the motherboard / system board.
Stefanie February 23, 2011 I just recieved a PC from a friend who wanted me to take a look at it and see if it is worth the price to fix Replace the failed component. Jay Search Computer Repair Advice On Google Plus! this content Vincent & Grenadines Suriname Swaziland Sweden Switzerland Taiwan Tajikistan Tanzania Thailand Togo Trinidad & Tobago Tunisia Turkey Turkmenistan Turks & Caicos Islands Uganda Ukraine United Arab Emirates United Kingdom United States
Power Light State Description Off Power is off, light is blank. All I've got to go on are the blinking keyboard light codes. #4 shamrin, Nov 1, 2010 B Trevathan Expand Collapse Member Likes Received: 17 Location: Tennessee, USA shamrin said: Lucia St. When the DELL logo appears, press
I'm wondering if the CMOS data got corrupt and changing the battery reset the CMOS data. Lucia St. A possible system board failure has occurred. The following article is a reference guide to the codes available on each model and what those codes actually mean.
September 7, 2011 4:37 pm Dell Latitude E6400 USB Audio Circuit Board Removal and Installation... Eric April 9, 2014 can somebody help me? Thank you Kelly C. Replace the system board.
Now I'm trying to reload windows with a cd. I have been trying to figure this out for a long time , hope I haven't contacted you before. If else, replace the motherboard. Solid Green System is in S0 state, the normal power state of a functioning machine.The BIOS will turn the light to this state to indicate it has started fetching op-codes.
In order to achieve a speedy publication, Quick Tips may represent only partial solutions or work-arounds that are still in development or pending further proof of successfully resolving an issue. If two modules are installed remove one and test. A possible USB failure has occurred. Replace the processor S3 MEM 2, 7 2 blinks followed by a short pause, 7 blinks, long pause, then repeats Memory failures Memory subsystem configuration activity is in progress.
June 3, 2014 11:55 am Dell Latitude E7440 Bottom Mouse Buttons Removal and Installation... Power LED and Diagnostic LEDs Light Pattern Problem Description Suggested Resolution Diagnostic LEDs Power Button LED The computer is either turned off or not receiving power.