Home > Error Code > Dell Autoloader Error Codes

Dell Autoloader Error Codes

Contents

If a cartridge is in the drive, the ready/activity LED flashes green until the cartridge is rewound. All other errors occurring during the PowerVault 120T DLT1 POST displays ROBOT POST on the Operator's Panel LCD. AC ON appears on the LCD. The recommended steps to follow are set out below: Press and hold the eject button for 10 seconds, then release. check over here

This includes, but is not limited to keeping PowerVault 120T DLT1 away from open windows, fan heaters, and doors. bT FW NN, where NN is the revision number of the firmware, appears on the LCD. LOAD FIRMWARE (LOAD FW) Whenever new firmware for the PowerVault 120T DLT1 is released, complete instructions on how to use the LOAD FIRMWARE function to perform the upgrade is included with The PowerVault 120T tracks the following events: Front Pick Cartridge Rear Pick Cartridge Drive Pick Cartridge Front Place Cartridge Rear Place Cartridge Drive Place Cartridge Front Pick Retries Rear Pick Retries http://en.community.dell.com/support-forums/storage/f/1216/t/19403374

Dell Tape Autoloader

If the tape appears to be in good condition, repeat the update process. Is it a sticker? –Cylindric Dec 7 '11 at 13:43 2 Dell does not list any PowerVault LTO4 drives as having a display/screen on them. When the update process is completed, the PowerVault 120T automatically unloads the tape and returns it to slot 2. The LCD Code "6" means "Tape drive or media error." The complete manual is on Dell's website.

Peter Like 0 Reply You have posted to a forum that requires a moderator to approve posts before they are publicly available. We will be looking into our other options with Dell now. Is there a manual way to remove the tape without damaging it? Dell Powervault Error Code 6 SCSI Adapter Card Installation: Verify the SCSI adapter card and drivers were correctly installed.

If this solves the problem, the cartridge was probably showing signs of frequent use or age. Hp Autoloader First, the drive is not cleaned upon request and second, improper data cartridges are added to the PowerVault 120T DLT1. According to the information I have, this indicates either a fault with the tape cartridge you are using or a fault with the tape backup unit itself. https://community.spiceworks.com/topic/408540-dell-powervault-114t-led-codes Termination: Make certain all SCSI buses are properly terminated.

Divisibility Proof How much should the average mathematician know about foundations? Tape Drive Error Code 6 After entering the DIAG MENU, press the MODE button until UPG DRV FW appears on the LCD. John CDell | Social Outreach Services Get Support on Twitter @DellCaresPro Download the Dell Quick Resource Locator app today to access PowerEdge support content on your mobile device! (iOS, Android, Windows) This function is used when the application software does not support an auto cleaning cycle and slot 7 is dedicated for data storage rather than a cleaning cartridge.

Hp Autoloader

Als u deze browserversie gebruikt, kunnen een aantal functies op onze website er anders uitzien of zich anders gedragen dan u gewend bent. Continued Press the SELECT button to disable the AUTOCLEAN function. Dell Tape Autoloader Snap! Sony Autoloader Press SELECT.

First, use the EJECT SLOT mode to empty slot 7. check my blog as i understood device is dead and i should send this device for repair...? Use the front panel to replace the cleaning cartridge with a new one. CYCLE AC is displayed on the LCD when the drive issues a cleaning tape expired condition during cleaning. Ibm Autoloader

Pressing SELECT, while in this menu, will cause the previous STOP SEQ request to be canceled and Sequential mode will continue with the current cartridge as if STOP SEQ had never If this solves the problem, writing to data is successfully completed. What do these mean, and how can I fix them? http://completeprogrammer.net/error-code/dell-error-codes-ide.html The PowerVault 120T DLT1 will return to LdR REAdY, disabling AUTOCLEAN.

Posted by Peter-ServIS on 14 Oct 2011 16:21 Hi All, The manual eject process did not work for us either. Dell Powervault 114x Error Codes Attempt to determine the exact location of the problem. The PowerVault 120T DLT1 will move the cleaning cartridge from slot 7 to slot 2.

Thanks for the replies!

Posted by Dell-Bob D on 8 Sep 2011 9:02 If a fix is found without a warranty repair can we get the answer posted back to the forums so others may Text Quote Post |Replace Attachment Add link Text to display: Where should this link go? dSP bT FW appears on the LCD. Dell Powervault 124t Manual Press SELECT.

LOAD FW Allows upgrading of the PowerVault 120T DLT1 firmware via the SCSI bus. If SELECT is pressed before placing the cleaning cartridge in slot 2, the PowerVault 120T DLT1 will continue to display the blinking CT 2 (SEL) message. Loader and Drive Operational Problems Occasionally, problems occur impacting the operation of the PowerVault 120T DLT1 and/or the DLT1 drive for two reasons. http://completeprogrammer.net/error-code/dell-hdd-error-codes.html Try writing to the cartridge.

This forces the application to re-map the PowerVault 120T DLT1.