Home > Error Code > Dell 1-3-2 Error Code

Dell 1-3-2 Error Code

Contents

Try copying the file to a different disk or use a larger capacity disk. Most beep codes indicate a fatal error that prevents the computer from completing the boot routine until the indicated condition is corrected. I also saw it could be something in the BIOS, but how do I get into that if I can't get past POST? When the boot device list appears, highlight Boot to Utility Partition and press . http://completeprogrammer.net/error-code/dell-error-code.html

Ensure that the memory you are using is supported by your computer. These beeps inform you that your hardware is in good working order. You can only upload videos smaller than 600MB. If the LED still does not illuminate, remove the PSU connections from the system board, then press and hold the power supply button. http://en.community.dell.com/support-forums/desktop/f/3514/t/19344616

Dell Error Code 123

Also, combining the configuration to validate appropriate combination. If the problem persists, try another drive. I have lots of Compaq power supply's laying around, so I figured to use one of these PSU's. Determine if a conflict exists by removing an expansion card (not a graphics card) and restarting the computer.

Welcome to Bleeping Computer! Reinstall the memory modules and, if necessary, replace them. If available, swap with a verified working hard drive & cable to test. Dell Optiplex 760 Error Codes 1 3 Memory modules are detected, but a memory failure has occurred.

KEYBOARD CONTROLLER FAILURE For external keyboards, check the cable connection. All Replies Posted by RoHe on 31 Aug 2010 17:38 The beeps and light code both indicate a RAM problem. No, create an account now. http://www.dell.com/support/article/us/en/04/SLN284978/en Laden...

I didn't know that the memory specs were so important. Dell Optiplex 980 Error Codes 1 3 Posted by mike25363687 on 9 Jan 2011 22:55 Well the clues about wiggling the heatsink have me pointed in the right direction. These can be audible beeps, power buttons that display different states and colours, specific diagnostics LEDs or a combination of them all, in order to indicate at which point during the Contact Dell Technical Support.

Dell Error Codes 1 3 4

Non-system disk or disk error The floppy disk in drive A does not have a bootable operating system installed on it.

You must put the ram in the slot 1 for the system. Dell Error Code 123 Errors Displays error conditions encountered, error codes, and the problem description. Dell Optiplex 790 Error Codes 1 And 3 Reinstall the memory modules and, if necessary, replace them.

WARNING: BATTERY IS CRITICALLY LOW The battery is running out of charge. have a peek at these guys Shut down and restart the computer. Contact Dell Technical Support. Again no beeps, diagnostic light pattern is GGGY. Dell Optiplex 960 Error Codes 1 And 3

Reinstall the memory modules and, if necessary, replace them. You'll need to troubleshoot if it's a memory issue or possible Motherboard issue. NO BOOT DEVICE AVAILABLE The computer cannot find the hard drive. check over here Thank you SO MUCH!!!!

The diagnostics LEDs moved from the rear of the chassis to the front under the audio ports. Dell Beep Codes 1 3 2 Memory modules have been detected but appear to be incompatible or in an invalid configuration. Bypass power strips, power extension cables, and other power protection devices to verify that the computer turns on properly.

Several functions may not work.

A weak battery can cause the symptoms you see. Does this mean that there is a memory problem? Thanks in advance Like 0 Reply You have posted to a forum that requires a moderator to approve posts before they are publicly available. Dell Optiplex 745 1-3-2 Beep Code Does this mean that there is a memory problem?

Posted by SpeedStep on 1 Sep 2010 11:04 The ram needs to be installed in matching pairs with 1 exception You can get by with 1 ram stick in the 4 Reset failed The disk reset operation failed. Most replies on forums (including this one) consist of either re-seat the RAM (which I've tried more than enough times) or replace motherboard. this content I was able to get it to come up just fine once this morning, then it locked up and when I rebooted, I got the same results. 0 Question by:spinsouth Facebook

Occasionally, reseating the memory modules may fix the beep code errors. Disconnect all internal and external peripherals, and restart the computer. Comment Submit Your Comment By clicking you are agreeing to Experts Exchange's Terms of Use. Security override Jumper is installed.

Posted by jorx on 1 Sep 2010 9:38 I have been testing both memory cards (there are only two), and the result is the same for both. i had exactly this problem and after removing the RAM from slot1 my computer would start to boot. NOT ENOUGH MEMORY OR RESOURCES. Diagnostic LEDs for the OptiPlex series (2005 to 2009) This series had a combination of Power button LED states and the A, B, C, B, block was replaced with 1, 2,