Home > Error Code > Debug Card Post Error Codes

Debug Card Post Error Codes

Contents

Pass control to the adaptor ROM at E000h next Erase F2 prompt A9 Returned from adaptor ROM at E000h control. The fourth function symbol of main menu,start to test the card itself. It will return round. Computeka Global 11.312 weergaven 4:54 Motherboard Diagnostic Debugger Card (4-digit LED) video demo - Duur: 2:54. this contact form

first the POST card are is placed inside the PCI slot of the motherboard. The first function symbol of main menu,then enter the function of thumbing through POST codes after it displayed for about half a second. 2--- Press and hold the switchfor about Take a moment and do a search below! 1250 Rogers Street, Suite C, Clearwater 33756, Florida, USAPhone: 1800-480-8204 © Copyright 2002 -    |   Capetronics Inc   |   All Rights Reserved   |   Privacy Portal Search Member List Calendar Help Initialize the local IDE bus.

Debug Card Error Codes And Solution

If press and hold the function switch for about 0.8 second twice, it will exit thumbing through POST codes and enter the second function of main menu, at the same time Configure the hard disk drive controller next. Reset the hard disk controller next. 8E The hard disk controller has been reset. if everything is good then the BIOS could be bad so reprogram the BIOS.

Should be on when power is supplied to the motherboard even without CPU. =>BIOS- BIOS Read Signal. ACS Data Recovery 814.182 weergaven 18:28 Test laptop motherboard (Debug card 3 in 1) - Duur: 1:23. If it displays from "0000"??| "1111" to "FFFF" after it displayed for about half a second. 5--- Press and hold the switch for about 0.8 second (The fifth time). Debug Card Error Code 0000 The time of PCI that the resetting signal needs is not always synchronized with the time of ISA .So sometimes the code begin to be displayed when the card in the

Some of these motherboard POST diagnostic tools are based off of the PCI slot (also known as EISA). If the man board hasn't run, the LED is off. It is a powerful diagnostic tool. http://www.capetronics.com/pdf/DC-0020.pdf CPU is testing the register inside or the test fails, please check the CPU or replace it.

Disable shadow and execute code from the ROM.08 Early chip set initialization The CMOS checksum is computed. Diagnostic Card Error Codes Detect and initialize video adapter. 0E Test Video Memory and write sign-on information to screen. Initialize I20 support 48 Reserved Patterns write in base memory. hindi typing kaese shike कंप्यूटर हार्डवेयर सीखे हिंदी में C...

4 Digit Debug Card Error Codes

As long as the monitoring value is large than 0500, PC Analyzer is all right. 3--- Press and hold the switch for about 0.8 second (The third time).

mostly when address signal is inappropriate the card will display this error code. Debug Card Error Codes And Solution Sometimes there is so short duration of cycle frame signal that you cannot feel the FRAME LED have been on by naked eyes. 4 Digit Debug Card Error Codes Pdf C7 OEM specific?aShadow video/system BIOS after memory proven good.

The codes that haven't been defined is not included in the table. 5. http://completeprogrammer.net/error-code/debug-card-error-code-ff.html To resolve this, clean the RAM pins and RAM slot and reinstall the RAM. (clean the RAM pins using a pencil eraser/rubber) or replace the RAM. James Davis 218.750 weergaven 4:58 Meer suggesties laden... Our new and improved design of Debug Card diagnostic card can work with almost all popular types of CPUs, Motherboards, and BIOSes. Debug Card Error Code Download

Initializing CMOS RAM if the Initialization CMOS RAM in every boot AMIBIOS POST option was set in AMIBCP or the key was pressed. If not, execute ISA tests and clear EISA mode flag. If it displays from "0000"??| "1111" to "FFFF" after it displayed for about half a second. 5--- Press and hold the switch for about 0.8 second (The fifth time). navigate here Initialize EISA extended registers. 04 RAM must be periodically refreshed to keep the memory from decaying.

B1 Unclaimed NMI. Diagnostic Card Error Codes List Should be on under normal circumstances and flashes when a PCI Frame Signal is detected. =>RST- Reset. Fault Finding by Diagnostic Card..online Chip Level Course - Duur: 18:01.

Display a soft error and check for a password or by passing WINBIOS is Set up next.

After it displayed for half a second, the POST code will be displayed, and the thousands digit and the hundreds digit indicate the hexadecimal POST code;the tens digit and units digit Get CPU type 05 Keyboard Controller Initialization The BIOS stack has been built. The LED should be on, As long as the Power is on after you plug the card in the ISA slot on the main board. Dell Post Error Codes C4 Initialize system error handler C5 Enable OEM Specific-Early Shadow for Fast Boot PnPnd dual CMOS (optional) C6 External Cache Size

Perform any required initialization before the Coprocessor test next. 9C Required initialization before the Coprocessor test is over. The definition of "BIOS" LED of PI0050A is opposite of "BIOS" LED of two-bit-code PC Analyzer and PI0050. The initiatory function symbol of main menu,The Start automatic diagnosis after it has displayed. (but the display is so fast that you cannot see. his comment is here The protected mode memory test is about to start. 3C Setup Enabled Advanced configuration of chipset registers 3D Detect if Mouse is Present, Initialize

Check for a soft reset and clear the memory below 1 MB for the soft reset next. Laptop Care LCIIT - Chip Level Repairing Institute 77.884 weergaven 18:01 POST DEBUG CARD (Hindi Part 4) - Duur: 9:49. Het beschrijft hoe wij gegevens gebruiken en welke opties je hebt. IF it is lit (ON) continuously then the reset signal is incorrect or it is totally absent. 12V Power Supply when this LED in ON it informs about the presence of

E1-EF Setup pages: E1 = page 1, E2 = page 2, etc. Load alternate registers with initial POST values 12 Reserved Next, disabling DMA controllers 1 and 2 and interrupt controllers 1 and 2 Restore CPU control word during Configure the timer data area and printer base address next. As there are more and more different kinds and structures of the motherboard, and the codes of BIOS POST is updated constantly, so the cause of trouble that error code indicates