I just compiled 2.6.17-rc3 with debug turned on for USB, and here is th eoutput if it helps. I will try this but I'm not sure this is the problem because *all* of my USB devices do not work so I know its not a problem with the cable Comment 10 Greg Oliver 2006-07-08 12:58:45 UTC I have seen this probolem with my Motorola Phone since 2.6.13 I believe. iulian (iulian-ghinea) wrote on 2009-12-22: #49 A solution for my case: I have a scanner: HP Scanjet 4370 and it was not recognized by th system. click site
Comment 14 Phil Lello 2007-10-15 08:16:20 UTC I'm seeing this problem with my Scanjet 5300C on Ubuntu 7.04 with 2.6.20-16. from my dmesg: ====================================== [15571.551295] usb 1-2: new high speed USB device using ehci_hcd and address 3 [15581.914390] usb 1-2: device not accepting address 3, error -110 [15582.026381] usb 1-2: new I found this message in dmesg after doing it: hda-intel: IRQ timing workaround is activated for card #0. Affecting: linux-source-2.6.15 (Ubuntu) Filed here by: Luke Hoersten When: 2006-07-27 Completed: 2009-07-11 Target Distribution Baltix BOSS Juju Charms Collection Elbuntu Guadalinex Guadalinex Edu Kiwi Linux nUbuntu PLD Linux Tilix tuXlab Ubuntu https://www.redhat.com/archives/rhl-list/2007-December/msg01356.html
However i have a built in USB camera that seems to be recognized. All rights reserved. I tried adding an extra usb disk but it fails with the same message.
And does it get asserted when you boot the system? The VBUS reference was not being fed back into the Phy correctly Works great now! Download the new AJAX search engine that makessearching your log files as easy as surfing the web. Device Not Accepting Address 2 Error 71 I had the same problem with a powered USB hub.
So I guess a BIOS upgrade won't make a difference.Anyone else got a similar problem? Device Not Accepting Address Error 32 Booted. 2) Mobo ports: Connected USB stick to motherboard USB port on the back of the computer. 3) Success: Rythmbox "Music Player" automatically started. Type uname -a and take note or memorize the exact kernel version numer you are using. 4. Comment 4 Alan Stern 2006-02-15 14:34:54 UTC A related bug report is #5777.
I can see a differential signal on the D+ and D- pins and VBUS is 5v. "device Not Accepting Address 10, Error -71" libata version 3.00 loaded. [ 22.690860] usbcore: registered new device driver usb [ 22.690938] ahci 0000:00:12.0: version 3.0 [ 22.690974] ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 22 (level, low) -> IRQ Feb 5 09:14:47 mucnb004 kernel: [ 1546.450023] uhci_hcd 0000:00:1d.1: HC died; cleaning up Feb 5 09:14:47 mucnb004 kernel: [ 1546.530137] hub 3-0:1.0: cannot reset port 2 (err = -19) Feb 5 At least the USB drive was automatically mounted after that.
When I try to mount them again after such crashing (or just after having them unmounted manually before), they won't work anymore. However, in case #2 there is still a problem from an end-user point of view: the error message is logged to syslog once a second. Device Not Accepting Address Error 71 FedoraForum.org is privately owned and is not directly sponsored by the Fedora Project or Red Hat, Inc. Device Not Accepting Address Error 110 If this issue still exists in a supported series, please file a new bug.
Buzz atdt911 (ori-ab) wrote on 2008-04-08: #16 I'm having this problem on my wi-fi usb dongle (zd1201 chipset). http://completeprogrammer.net/device-not/device-not-accepting-address-2-error.html DOWNLOAD SPLUNK!http://firstname.lastname@example.orgTo unsubscribe, use the last form field at:https://lists.sourceforge.net/lists/listinfo/linux-usb-devel 4 Replies 115 Views Switch to linear view Disable enhanced parsing Permalink to this page Thread Navigation driversbin driversbin 2005-12-07 06:51:46 UTC i have a laptop t61p lenovo that can not access a Corsair usb flash pen 8gb (flash voyager) but on the same port i can use a sandisk 4gb without any If you're not using 2.6.14 or later, tryupgrading before doing anything else.It's hard to tell just what is going wrong without more debugginginformation. Device Not Accepting Address Error 62
Christopher M. Stop! Powered By GSpeech Ubuntu Forums > The Ubuntu Forum Community > Ubuntu Official Flavours Support > Hardware > [xubuntu] USB mouse not working PDA View Full Version : [xubuntu] USB mouse navigate to this website Controller is probably using the wrong IRQ.usb 2-2: device descriptor read/64, error -110Could this be causing all these problems?
If I plug it into the onboard OHCI controller, it works. Device Not Responding To Set Address This information hasn't been pulled yet. Offline #8 2007-11-05 10:13:48 zenlord Member From: Belgium Registered: 2006-05-24 Posts: 1,209 Website Re: usb x-x: device not accepting address x, error -62 I have not had the time to test
Reboot and test. The first usb disk continues to work, however. bp112 View Public Profile Find all posts by bp112 #2 23rd July 2011, 08:07 PM alexeik Offline Registered User Join Date: Feb 2011 Location: Moscow, Russia Posts: 105 Ubuntu Usb Device Not Accepting Address Bill.
Luke Hoersten (lukehoersten) wrote on 2006-08-19: #3 Now none of my USB devices work, not even my printer. You may save yourself some time. Download the new AJAX search engine that makessearching your log files as easy as surfing the web. my review here I realize it's a rather long thread but I'd draw your attention to https://bugs.edge.launchpad.net/ubuntu/+source/linux-source-2.6.20/+bug/88746/comments/228 which was from one of our kernel devs.
My workaround has been to add "nomodeset" parameter to kernel boot parameters. I have attached my dmesg output. Any suggestions, please? Any idea what's going on?
It's been sitting there for over a month now waiting for you ... This afternoon I will try an older livecd.Zl. Always back up config files before editing them: sudo cp /etc/modprobe.d/options /etc/modprobe.d/options.backup1 Now open /etc/modprobe.d/options in write mode: sudo gedit /etc/modprobe.d/options 2. The logging of this error should be radically reduced, I'd really prefer, say, once an hour to once a second.
Seemingly reloading the module (scsi_mod) does not cause the new configuration to take hold. No amount of fussing with services or modules or rebooting brings it back.