Home > Dell Poweredge > Dell Poweredge 1900 Error Codes

Dell Poweredge 1900 Error Codes

Contents

System reset POST E2013 Shadow BIOS Fail High 0x83 -- BIOS failed to copy its flash image into memory. Time-of-day not set - please run SETUP program Incorrect Time or Date settings or defective system battery Check the Time and Date settings. If the problem persists, replace the system battery. Covered by US Patent. http://completeprogrammer.net/dell-poweredge/dell-poweredge-t605-error-codes.html

N/A Any N/A SBIOS N/A 0x05– BIOS shadow into memory. System reset POST E2018 ProgTimer High 0x88 -- Programmable interval timer error. See "Microprocessors" for instructions. E1A10 PDBPwrCable High PDB power cable to the planar is missing or bad and system will not power on.

Dell Poweredge 2950 E1000 Failsafe

AC Cycle or SEL clear Any E1217 5VPwrGd High 5V voltage regulator has failed. See "Jumpers, Switches, and Connectors" for instructions. Drive not ready Diskette missing from or improperly inserted in diskette drive Reinsert or replace the diskette. Amount of memory has changed Missing or faulty DIMMs Check that DIMMs have not been removed.

N/A Any N/A E122A N/A 0x2a–SIO failure. N/A Any N/A E.11 N/A 0xC4–BIOS shutdown test failure. Could be the result of bad memory. I use mine on a daily basis.

Posted by aungkhk on 18 May 2013 1:25 Thanks for your answer Like 0 Reply You have posted to a forum that requires a moderator to approve posts before they are E1216 3.3v Regulator Failure Detected mode switch from RAID to SCSI on the onboard RAID channel. The error codes and their definitions are separated into categoriesdepending on the source of the error.Cable and Board Presence - Message Code: "x1Axx" Message Code Message String Message Priority Message Comments https://www.experts-exchange.com/questions/27789122/Dell-PowerEdge-1900-front-LED-message.html Feel free to check out this quick video on how to manage your email notifications.

Regards, Geoff PDell | Social Outreach Services - EnterpriseGet Support on Twitter @DellCaresProDownload the Dell Quick Resource Locator app today to access PowerEdge support content on your mobile device!(iOS, Android, Windows) If the error doesn't clear, the motherboard will need to be replaced. Any E1620 PS #Input Range Low Power supply #'s AC/DC input is outside of the allowable range. N/A Any N/A E0119 N/A 0x29–Parity error.

E1216 3.3v Regulator Failure

System reset POST E2011 MemConfigErr High 0x81 -- Memory detected but is not configurable. AC Cycle or SEL clear Any E122C CPU Power Fault High A voltage regulator failure was detected when the processor regulator(s) was enabled. Dell Poweredge 2950 E1000 Failsafe What OS is running on it? Dell E1216 Timer chip counter 2 failed Defective system board Replace the system board.

If the problem persists, replace one or more DIMMs. More about the author AC Cycle or SEL clear POST, After POST Power Supplies - Message Code: "x16xx" Message Code Message String Message Priority Message Comments Minimum Action Required to Remove Message from LCD System If the message reappears, set the configuration jumper to Maintenance mode and restart the system to return all settings to their defaults Real time clock error The RTC has failed the Could be result of bad memory, mismatched memory or bad socket. E1000 Failsafe Call Support

System reset POST E201E POSTMemTest High 0xC1 -- BIOS POST memory test failure. See "Troubleshooting the Microprocessors" on page 118. Back to Contents Page Home· Forums· About Us· Awards· Contact Us· Upgrade your BIOS BIOS UPDATES Click to scan for Bios Updates BIOS PostCodes Acer ALR AMIT/AMI Arche Legacy AST AT&T http://completeprogrammer.net/dell-poweredge/dell-poweredge-2850-error-codes.html No boot sector on hard-disk drive Incorrect configuration settings in System Setup program, or no operating system on hard-disk drive Verify the hard-disk drive System Setup information is correct.

Remove one or more DIMMs so that total memory is 2 MB or less. Unsupported RAID key detected! Uncorrectable memory error previously detected in xxxx xxxxh Improperly seated or faulty DIMMs Remove and reseat the DIMMs.

Have you rebooted?

Chassis lid is returned to the system. The system BIOS has reported a processor bus parity error. AC Cycle or SEL clear POST, After POST E1711 PCI PERR Slot # High BIOS has reported PCI parity error on a component that resides in slot #. Document ID:7921054Creation Date:16-APR-08Modified Date:26-APR-12NetIQPlateSpin Forge Did this document solve your problem?

Any help would be appreciated! 0 Question by:hodgem Facebook Twitter LinkedIn Google LVL 5 Best Solution byMetaltree Well from the sound of it, looks like you need a new fan. See "Getting Help" on page 131. Failing device is reseated/replaced/repaired. news Read fault Requested sector not found Faulty diskette, diskette/tape drive subsystem, or hard-disk drive subsystem (defective system board) Replace the diskette or hard-disk drive.

Keyboard controller failure Defective keyboard/mouse controller (defective system board) Replace the system board. AC Cycle or SEL clear Any E1221 Flex BayPwrGd High Flex Bay voltage regulator power good has failed. Several different types of messages can indicate when the system is not functioning properly: System messages System beep codes Warning messages Diagnostics messages Alert messages SCSI hard-disk drive indicator codes System Clear the log and see if the error returns.

Recommend it to your friends. One microprocessor is operating at a different internal frequency or cache size than the other microprocessor Ensure that both microprocessors are identical in type, operating frequency, and cache size. If the problem persists, replace the system board. 4-4-1 Super I/O chip failure (defective system board) Replace the system board. 4-4-2 Parallel-port test failure (defective system board) Replace the system board. System reset or device is reseated/replaced/repaired.

N/A Any N/A VIDEO N/A 0x40–Display sign-on. E1418 CPU # Presence E141C CPU Mismatch E141F E1420 E1421 E1422 E1618 CPU Protocol CPU Bus PERR CPU Init CPU Machine Chk PS # Predictive The system BIOS has reported a AC Cycle or SEL clear Any E1227 LinearPwrGd High Linear voltage regulator(s) has failed. Any E1311 RPM Fan Mod #A Low RPM of fan A in the # module is outside of the intended operating range.

E1610 PS # Missing Low Power supply # was removed or is missing from the system. Drive rebuilding The drive online indicator blinks rapidly. They can assist you with identifying a problem and may provide you with information to help you resolve the problem. Reinstall the hard-disk drive.

There are many reasons for wanting to remove this icon. If the problem persists, replace the system board. Diskette subsystem reset failed Faulty diskette/tape drive controller (defective system board) Replace the system board. If there is an actual issue, it will come back; if it just got "stuck", then clearing it will reset it so you can monitor for real issues (like the fan