Home > Dell Optiplex > Dell Optiplex Post Error Codes

Dell Optiplex Post Error Codes

Contents

Take the appropriate action to resolve the problem. If available, install a working graphics card into your computer.If the problem persists, contact Dell . No POST, No Power, No Video on a Dell Desktop Computer. If the problem persists, the system board is probably bad. http://completeprogrammer.net/dell-optiplex/dell-optiplex-780-post-error-codes.html

If identified the memory failed, replace the memory. The delay between each set of beeps is 3 sec, and the beep sound lasts 300ms. A possible floppy drive or hard drive failure has occurred. You may have a defective sector or corrupted FAT on the hard drive.

Dell Optiplex 755 Error Codes

When the DELL logo appears, press immediately. A possible processor failure has occurred. CD DRIVE CONTROLLER FAILURE The CD drive does not respond to commands from the computer.

Shut down the computer, remove the hard drive, and boot the computer from a CD. Back to Contents Page Diagnostics Dell OptiPlex 780 Service Manual Dell Diagnostics Power Button Light Codes Beep Codes Diagnostic Lights Dell Diagnostics When to Use the Dell Diagnostics It is If the problem persists, try another drive. Dell Optiplex Gx520 Error Codes Probeert u het later nog eens.

The left column is for computers manufactured before 2006, the right column is for computers manufactured in 2006 and since. Dell Optiplex Gx270 Error Codes Repeat this process for each expansion card installed. If you are still unable to resolve the problem, contact Dell for technical assistance. http://www.dell.com/support/article/us/en/19/SLN293445 Memory modules are detected, but a memory configuration or compatibility error has occurred.

Diagnostic LED CodesBelow is a chart that provides information on what the LED diagnostics code mean for Optiplex and Latitude Computers. Dell Optiplex Error Codes 1 3 Optiplex Error Messages An Error Message may be displayed along with the accompanying beep code. NOTE: The Dell Diagnostics software works only on Dell computers. Shut down the computer, remove the hard drive, and boot the computer from a CD.

Dell Optiplex Gx270 Error Codes

If the LEDs never came on at any point then look into a power issue. read this post here To make it easy for service providers to implement the error codes, PC-Doctor released the Error Code Wizard. Dell Optiplex 755 Error Codes Look at the diagnostic LEDs for further information. Dell Optiplex Gx280 Error Codes Nederland Land selecteren Afghanistan Albanië Algerije Amerikaanse Maagdeneilanden Angola Anguilla Antigua en Barbuda Argentinië Armenië Aruba Australië Azerbeidzjan Aziatisch-Pacifisch gebied Bahama's Bahrein Bangladesh Barbados België Belize Benin Bermuda Bhutan Bolivia Bosnië-Hercegovina

No CPU present. news CMOS battery failure 6 Video BIOS Test Failure Video card / chip failure 7 CPU Cache Test Failure CPU failure 8 LCD LCD failure Identifying Dell Computer Models Using the Reseat any installed graphics cards. Look at the diagnostic lights to determine which state the system is in. Dell Optiplex Gx620 Error Codes

Press and hold the power supply test button on the rear of the power supply unit. Ensure that all hard drive and optical drive cables are properly connected to the system board . Occasionally, reseating the memory modules may fix the beep code errors. http://completeprogrammer.net/dell-optiplex/dell-optiplex-330-post-error-codes.html Link to Fix PSA 1000-0241PSA+ 2000-0241 Error enabling A20 gate.

Location and purpose of the power button LED and the diagnostic LEDs. Dell Optiplex 755 Error Codes 2 And 4 S8 MEM 3, 5 3 blinks followed by a short pause, 5 blinks, long pause, then repeats Memory configuration or incompatible error Memory subsystem configuration activity is in progress. instead If you receive this message after making changes in the setup program, enter the program and restore the original values(s) Press to resume, to Setup This message is

Then, shut down the computer, reinstall the hard drive, and restart the computer.

TIME-OF-DAY NOT SET-PLEASE RUN THE SYSTEM SETUP PROGRAM The time or date stored in the system setup program does not match the system clock. Write down any error codes listed. A possible graphics card failure has occurred. Dell Optiplex 960 Error Codes 1 And 3 Allow one minute for the power to drain.

INVALID CONFIGURATION INFORMATION-PLEASE RUN SYSTEM SETUP PROGRAM The system configuration information does not match the hardware configuration. System plugged in, but either turned off or in Windows Hibernation State. 1- Off2- Off3-Solid4- Off - Reserved 1- Off2- Off3- Solid4- Solid Suspend to RAM Windows Standby State. 1- Off2- DISK C: FAILED INITIALIZATION The hard drive failed initialization. check my blog Run the System Set tests in the Dell Diagnostics.

If identified the memory failed, replace the memory. Je kunt deze voorkeur hieronder wijzigen. Shut down and restart the computer. These codes are recognised across manufacturers and have remained the same for some time.

Link to Fix PSA 1000-0334PSA+ 2000-0334 User reported that graphics patterns were not displayed correctly. Windows XP: Click Start > Control Panel > Add or Remove Programs > Programs and Features. MEMORY ADDRESS LINE FAILURE AT ADDRESS, READ VALUE EXPECTING VALUE A memory module may be faulty or improperly seated. Another failure has occurred.

Diskette write protected The floppy disk is write-protected. Visit the Dell Drivers and Downloads website and input your Service Tag to get updates specific to your computer. Disconnect all internal and external peripherals, and restart the computer. Hard-disk controller failure The hard drive failed initialization.

Memory modules are detected, but a memory power failure has occurred. This series of beeps, called a beep code, can be used to help identify various problems. 3 means 3-3-3-3...That is 3 beeps and 3 beeps and ...: Endless looping until user The delay between each set of beeps is 3 sec, and the beep sound lasts 300ms. You could identify these system by their flat black and grey front face.