Home > Dell Optiplex > Dell Optiplex Error Codes 1 3

Dell Optiplex Error Codes 1 3

Contents

Advertise Media Kit Contact Fargo Wiki is a Fandom Lifestyle Community. Possible peripheral card or system board failure has occurred. On the next startup, the computer boots according to the devices specified in the system setup program. Another failure has occurred. have a peek at these guys

The power light states are shown in following table. If you have problems with an IEEE 1394 device not provided by Dell — Contact the IEEE1394 device manufacturer. Press a key on the keyboard, move the mouse, or press the power button to resume normal operation. The key to these codes are displayed in the table below. http://www.dell.com/support/article/us/en/04/SLN284978/en

Dell Optiplex 990 Error Code 1 3

drive letter :\ is not accessible. Appropriate memory modules were detected but a memory failure has occurred. Clean the drive or disk — See the Dell Technology Guide for more information on cleaning your computer. A possible processor failure has occurred.

Click the area you want to change or click the Display icon. Power off computer, leaving the computer plugged in. Errors Displays error conditions encountered, error codes, and the problem description. Dell Optiplex Gx280 Error Codes When the DELL logo appears, press immediately.

Turn on the computer and the monitor and adjust the monitor brightness and contrast controls. Dell Optiplex 990 Error Code 1 3 4 Steady Amber Memory modules are detected, but a memory power failure has occurred. If available, install verified working memory of the same type into your computer. http://www.tomshardware.com/answers/id-1870150/optiplex-780-boot-lights-blinking-power-button-blinking-amber.html ab8a 46.194 weergaven 2:38 Dell Optiplex 760 SFF - RĂ©paration alimentation - Duur: 53:58.

Restart the computer and log on to the network again Check your network settings — Contact your network administrator or the person who set up your network to verify that your Dell Optiplex Gx620 Error Codes A possible coin cell battery failure has occurred. If available, install a working graphics card into your computer. Possible system board failure.

Dell Optiplex 990 Error Code 1 3 4

Replace the CPU with a known good CPU. Tab Function Results Displays the results of the test and any error conditions encountered. Dell Optiplex 990 Error Code 1 3 Replace the processor S3 MEM 2, 7 2 blinks followed by a short pause, 7 blinks, long pause, then repeats Memory failures Memory subsystem configuration activity is in progress. Dell Optiplex 755 Error Codes CAUTION: If your computer came with a PCI graphics card installed, removal of the card is not necessary when installing additional graphics cards; however, the card is required for troubleshooting purposes.

For information about your graphics card, go to support.dell.com. http://completeprogrammer.net/dell-optiplex/dell-optiplex-330-error-codes-3-4.html The following table lists the beep codes that may be generated during the POST. These can be audible beeps, power buttons that display different states and colours, specific diagnostics LEDs or a combination of them all, in order to indicate at which point during the Replace the processor with a known good processor. Dell Optiplex Gx270 Error Codes

This message may help support personnel diagnose and fix the problem(s).If an error message occurs in a program, see the program's documentation. Contact Dell (see Contacting Dell). When the DELL logo appears, press immediately. check my blog Reinstall the processor and restart the system.

Check the monitor settings — See the monitor documentation for instructions on adjusting the contrast and brightness, demagnetizing (degaussing) the monitor, and running the monitor self-test. Dell Optiplex Gx520 Error Codes If two or more memory modules are installed, remove the modules, then reinstall one module and restart the computer. Power off computer, leaving the computer plugged in.

If identified any of the component failed, replace the component.

Code Cause 1-1-2 Microprocessor register failure 1-1-3 NVRAM 1-1-4 ROM BIOS checksum failure 1-2-1 Programmable interval timer 1-2-2 DMA initialization failure 1-2-3 DMA page register read/write failure 1-3-1 through 2-4-4 DIMMs When the test completes, record the test results and then press any key to return to this menu. Replace the CPU fan. Dell Optiplex Beep Codes For more information about the type of memory supported by your computer, see Memory.Run the Dell Diagnostics (see Dell Diagnostics).

NOTE: The next steps change the boot sequence for one time only. Turn off nearby devices to check for interference. Solid White System is in S0 state. news Back to Top 1.

Drive Problems WARNING: Before working inside your computer, read the safety information that shipped with your computer. Remove all cards from the PCI and PCI-E slots and restart the computer. Reinstall the scanner driver — See the scanner documentation for instructions. If you purchased a sound card, ensure that the speakers are connected to the card.

For a parallel printer, ensure that the Print to the following port(s): setting is LPT1 (Printer Port). If that doesn't help then remove one module and try it. Ensure that the display/monitor is plugged into a discrete graphic card. ABCD MEM Memory subsystem configuration activity or failure Remove all memory from PC, does the LED code change?

Steady Green A possible graphics card failure has occurred. Extended Test Performs a thorough check of devices. Note : Please click on the title of the section you want to open below, in order to see the contents. Back to Contents Page Back to Contents Page Diagnostics Dell OptiPlex 780 Service Manual Dell Diagnostics Power Button Light Codes Beep Codes Diagnostic Lights Dell Diagnostics When to Use the

In some cases, you may have to restart your computer to restore computer resources. If two or more memory modules are installed, remove the modules, then reinstall one module and restart the computer. A possible system board failure has occurred. If the computer still fails to boot, inspect the processor socket for damage.If the problem persists, contact Dell (see Contacting Dell).

Parameters Allows you to customize the test by changing the test settings.