OptiPlex Beep Codes The computer might emit a series of beeps during start-up if the display cannot show errors or problems. The following article is a reference guide to the codes available on each model and what those codes actually mean. These indicators are merely a starting point to narrow down any troubleshooting you will carry out to identify the cause of your current issue. If you can assist to troubleshoot, narrow down the issue with reseating memory and swapping a known good memory if available. this content
Reinstall the memory modules and, if necessary, replace them. Link to Fix PSA 1000-0241PSA+ 2000-0241 Error enabling A20 gate. Shutdown failure A chip on the system board might be malfunctioning. Then, shut down the computer, reinstall the hard drive, and restart the computer. http://www.dell.com/support/article/us/en/19/SLN143065/EN
Look at the diagnostic lights for further information. Contact Us PSA+ 1000-0331 No video adapter found. If the computer boots, add the peripheral cards back one by one until you find the bad one. x:\ is not accessible.
Write fault on selected drive The operating system cannot write to the floppy or hard drive. two-tone siren Low CPU Fan speed, Voltage Level issue Additional information Additional information on the POST and how a computer works? INVALID CONFIGURATION INFORMATION-PLEASE RUN SYSTEM SETUP PROGRAM The system configuration information does not match the hardware configuration. Dell Optiplex Gx280 Beep Codes The message is usually followed by specific information-for example, Printer out of paper.
MEMORY WRITE/READ FAILURE AT ADDRESS, READ VALUE EXPECTING VALUE A memory module may be faulty or improperly seated. Correct the appropriate options in the system setup program. Reinstall the memory modules and, if necessary, replace them. http://www.dell.com/support/article/us/en/19/SLN293445 The beep code is a pattern of sounds: for example, one beep, followed by a second beep, and then a burst of three beeps (code 1-1-3) means that the computer was
The computer failed to complete the boot routine three consecutive times for the same error. Dell Optiplex Gx260 Beep Codes Reinstall the memory modules and, if necessary, replace them. Ensure that no special requirements for memory module/connector placement exist. Johnny Phung 1.719.724 weergaven 11:59 How To Fix Computer Three Beeps Problem - Duur: 2:58.
If the problem persists, try another drive. http://www.dell.com/support/article/us/en/04/SLN284918/en Start the Dell Diagnostics from either your hard drive or from the Drivers and Utilities media. Dell Optiplex Beep Codes 1-3-2 KEYBOARD CONTROLLER FAILURE For external keyboards, check the cable connection. Dell Optiplex 755 Beep Codes If the message reappears, contact Dell.
Hard-disk drive failure The hard drive failed initialization. news Time-of-day clock stopped The battery might be dead. This beep code tells you that the computer encountered a memory problem. Blinking Amber Initial State of LED at power up. Dell Optiplex Gx270 Beep Codes
If available, swap with a verified working optical drive and cable to test. If you need assistance in Downloading and Installing Drivers or BIOS. Inloggen 4 Laden... have a peek at these guys Je moet dit vandaag nog doen.
Log in om dit toe te voegen aan de afspeellijst 'Later bekijken' Toevoegen aan Afspeellijsten laden... Dell Optiplex Gx240 Beep Codes Run the Keyboard Controller test in the Dell Diagnostics. HARD-DISK DRIVE CONFIGURATION ERROR The computer cannot identify the drive type.
You can use this as a starting point to narrow down the proper troubleshooting guide you will need or you can contact technical support for further help and they will be SECTOR NOT FOUND The operating system cannot locate a sector on the hard drive. This article provides information on Dell Optiplex & Vostro Beep Codes and Error Messages. Dell Optiplex Gx620 Beep Codes OPTIONAL ROM BAD CHECKSUM The optional ROM has failed.
Contact Dell 7 CPU Cache test failure Contact Dell Back to Top Artikel-id: SLN284918 Laatste wijzigingsdatum: 01/25/2016 08:24 AM Beoordeel dit artikel Nauwkeurig Nuttig Eenvoudig te begrijpen Was dit artikel If the error message still appears, see the software documentation. Log in om je mening te geven. check my blog If a large number of sectors are defective, back up the data (if possible), and then reformat the hard drive.