Home > Dell Optiplex > Dell 745 Error Codes 3 4

Dell 745 Error Codes 3 4

Contents

When to Use the Dell Diagnostics If you experience a problem with your computer, perform the checks in this section and run the Dell Diagnostics before you contact Dell for technical Close the test screen to return to the Main Menu screen. Light Pattern Problem Description Suggested Resolution The computer is in a normal "off" condition, or a possible pre-BIOS failure has occurred. NOTE: The Service Tag for your computer is located at the top of each test screen. http://completeprogrammer.net/dell-optiplex/dell-led-error-codes-755.html

No harm intended. The computer is in a normal on condition. Adamant IT 28.246 weergaven 10:03 [Solved] OptiPlex GX620 - Beep Code 1-3-2, RAM Error. - Duur: 5:37. Re-insert the memory and try again.

Dell Optiplex 745 Error Code 3 4

WeergavewachtrijWachtrijWeergavewachtrijWachtrij Alles verwijderenOntkoppelen Laden... If identified the component failed, replace the component. ABCD RCM BIOS checksum failure - Recovery mode Reset the BIOS and clear the NVRAM If this occurred after windows updates, check your startup wasn't corrupted. Repeat this process until you identify which card is malfunctioning.

Software ▼ Security and Virus Office Software PC Gaming See More... Double-click any device marked with an exclamation point to display the Properties window. Posted by goodtime212 on 8 Dec 2013 13:59 your problem is your memory. Dell Error Codes 3 4 Optiplex 755 If there is an error message on the screen identifying a problem with a device (such as the floppy drive or hard drive), check the device to make sure it is

Possible peripheral card or system board failure has occurred. Dell Optiplex 745 Error Codes 1 2 3 i think theres an issue with the graphics card no display at all. 0 LVL 23 Overall: Level 23 Components 8 PCs 6 Desktops_PCs 3 Message Expert Comment by:edbedb2009-10-05 I Hard-disk configuration error — Hard-disk controller failure — Hard-disk drive failure — Hard-disk drive failure — See Drive Problems.

Contact your technical support to take this further. 34 MEM Memory subsystem configuration activity or failure Remove all memory from PC, does the LED code change?

Alert! Dell Optiplex Gx620 Error Codes Off-Topic Tags How-tos Drivers Ask a Question Computing.NetForumsGeneral HardwareGeneral Solved What do the 1, 3, 4 green lights on the front Tags:Dell Optiplex 320 desktoppcproblems Monique Trujillo November 17, 2010 at Click Hardware Troubleshooter in the Search Results list. If else, replace the motherboard.

Dell Optiplex 745 Error Codes 1 2 3

Het beschrijft hoe wij gegevens gebruiken en welke opties je hebt. https://www.scribd.com/doc/55908294/Dell-OptiPlex-745-Quick-Reference-Guide Run the BIOS Recovery utility, wait for recovery completion, and then restart the computer. Dell Optiplex 745 Error Code 3 4 Metalzone 267.166 weergaven 2:45 No Power? Dell 745 Beep Codes The lights can be off or green.

That seems like the trick - new motherboard. have a peek at these guys If the LED still does not illuminate, the problem is probably with the power supply. Run the Dell Diagnostics to identify a more serious cause (see Dell Diagnostics). Computer Tips 102.002 weergaven 4:06 Amber orange light problem in DELL - Duur: 28:21. Dell Optiplex 745 Diagnostic Lights 3 4

If the LEDs never came on at any point then look into a power issue. If you are seeing an unrecognisable code, one that isn't listed above - then please get in touch with your local support straight away. IIRC, this is a DDR2/533 memory configuration and should run fine in single module mode. check over here Remove all peripheral cards from the PCI and PCI-E slots and restart the computer.

If it works then it's your PSU. 0 LVL 12 Overall: Level 12 Components 2 PCs 2 Desktops_PCs 2 Message Expert Comment by:WallD2009-10-06 Hi there are some diagnostic lights on Dell Optiplex Gx280 Error Codes If none of the memory failed, replace the motherboard. Blinking White System is in a low power state, either S1 or S3.

Diskette drive 0 seek failure — See Drive Problems.

If my answer was helpful, please use the 'Did this answer the question' and click: YesForum Member since 2001Iam not employed byDell Like 0 You have posted to a forum that Also, combining the configuration to validate appropriate combination. FrenchThe Future InternetSamsung camera ST500(TL220) User ManualDePauw Magazine Summer 2006Designing for digitalTrends in Video Games and GamingSamsung Camera ST66 English User ManualThe Dyslexic Reader 2006 - Issue 41Samsung ES65(SL50) English User Dell Optiplex 3010 Diagnostic Lights 3 And 4 A00 book.book Page 2 Wednesday, August 16, 2006 3:18 PM Contents 3 Contents Finding Information . . . . . . . . . . . . . . .

Code Cause 1-1-2 Microprocessor register failure 1-1-3 NVRAM read/write failure 1-1-4 ROM BIOS checksum failure 1-2-1 Programmable interval timer failure 1-2-2 DMA initialization failure 1-2-3 DMA page register read/write failure 1-3 If identified the memory failed, replace the memory. The device is not ready — The selected drive cannot read its medium. this content Bad command or file name — Ensure that you spelled the command correctly, put spaces in the proper place, and used the correct pathname.

If it doesn't contact your technical support If it does add the memory modules back one at a time until the fault re-occurs, test that module in another slot and contact Note : Please click on the title of the section you want to open below, in order to see the contents. Type hardware troubleshooter in the Search field and click the arrow to start the search. NOTE: The orientation of the diagnostic lights may vary dependent upon the computer type.

The symptoms don't point to memory, try a PCI graphics card to verify that the onboard video isnt dead. lilbit13007, Oct 20, 2011 #7 JHM banned Messages: 445 bye Last edited: Dec 16, 2012 JHM, Oct 21, 2011 #8 (You must log in or sign up to reply here.) If you run a test from the Custom Test or Symptom Tree option, click the applicable tab described in the following table for more information. This is the normal power states of a functioning machine.