This series of beeps, called a beep code, identifies a problem. A B Yellow and C D Green -- This means you have memory installed, but there is a problem with it. Memory modules are detected, but a memory failure has occurred.If you have one memory module installed, reinstall it and restart the computer. Read carefully, and understand the dangers of Static Electricity and How to avoid damaging your computer. have a peek at these guys
Code Cause 1-3-1 through 2-4-4Memory not being properly identified or used 4-3-1Memory failure above address 0FFFFh If you hear one of the following beep codes, see "Contacting Dell" in your Owner's I would pull the manual for your computer at the Dell sight. Memory, like all hardware, can fail. I tried last known good configuration which usually works on my pc, but it didn't do anything. original site
If the problem persists, see "Contacting Dell" in your Owner's Manual for instructions on obtaining technical assistance. I suggest you join our free forums so we can troubleshoot this more. If the computer starts normally, troubleshoot the last card removed from the computer for resource conflicts (see "Resolving Software and Hardware Incompatibilities" in the Owner's Manual). I think what went wrong is that the usb cord had been laying on my bed and (picked up static electric)and when I plugged it in zap….well it seems like the
Determine if a conflict exists by removing a card (not the video card) and then restarting the computer. I tried several different options but the OS just won't boot up. A possible floppy or hard drive failure has occurred.Reseat all power and data cables and restart the computer. Dell Dimension 4600 Memory When tried to switch on the PC, the front power light turns yellow and the CPU activity lamp turns green.
Bezig met laden. Dell Dimension 4600 Manual Pdf If you're comfortable doing so, you can remove the ram modules and try and reseat them. There will be troubleshooting a diagnostic codes for your specific model in that manual. Invalid Boot DisketteThe operating system cannot be located on drive A or drive C.Enter the system setup program and confirm that drive A or drive C is properly identified.
If the computer starts normally, move the memory module to a different connector and restart the computer. Dell Dimension 4600 Video Card Other failure has occurred.Ensure that the cables are properly connected from the hard drive, CD drive, and DVD drive to the system board. Diskette Boot FailureDrive A or B is present but has failed the BIOS POST.Ensure that the drive is installed correctly in the computer and defined correctly in the system setup program. Thanks Dave July 4, 2012 That's not uncommon.
Log in with Facebook Log in with Twitter Log in with Google Your name or email address: Do you already have an account? I checked the sequence of the beeps, and it is: 2 long, 2 short, 1 long, 1 short. Dell Dimension 4600 User Manual These advanced tools can generally point to the problem part if you know what you're looking for. Dell Dimension 4600 Drivers Jun 17, 2009 #4 deezee TS Rookie Topic Starter Dimension 4600 beeps, won't boot Can you tell me how to reseat the memory, or swap between slots??
Under tools>internet options>advanced, see if you have a button that says RESET. More about the author February 20, 2013 On the front of my computer the numbers 3 and 4 flash in the color of green when I turn my computer on, Please help me by telling If you do, click it. Jun 16, 2009 #2 deezee TS Rookie Topic Starter Dimension 4600 beeps, won't boot Thank you. Dell Dimension 4600 Hard Drive Removal
Refer to the Dell website for your specific model, as these lights can vary from model to model. If the problem persists, see "Contacting Dell" in your Owner's Manual for instructions on obtaining technical assistance. Reseating the memory modules may fix the beep code errors in the following table. http://completeprogrammer.net/dell-dimension/dell-dimension-4600-abcd-error-codes.html A B D Yellow and C Green -This means you could have a problem with your CPU.
We will list a few of the most common here, but there are certainly more on the Dell website. Dell Dimension 4600 Cpu Upgrade When we turn it on . Dell Computer Error Codes In addition to a beep code, your Dell PC might have diagnostic lights on the front panel, lights in the rear labeled A,B,C and D and even
It had developed booting problem during the last few months. Thomas Dave November 10, 2012 Sounds like a bad hard drive, Thomas. Then comes something about cryptnett dll not designed to run on windows and finally, Dell dock language file failed to load, check dell dock installation. Dell Dimension 4600 Power Supply Connect with me on: Google+ 25 Comments abdessamad bado November 30, 2009 dear sir my problem ihave a pc dell but does not work there is a light yellow in it
No memory modules are detected.Reinstall all memory modules and restart the computer. Michaelk May 29, 2011 Need help with a Dell Dimension 3000, which on boot only lights a steady green and yellow light. Maybe a replaceable chip, maybe not. news Sign up for a new account or log in here: Forgot your password?
Dave March 3, 2013 Hi Ed. A - yellow, B - green, C - yellow, D - green <--- Indicates a problem with the video card. your local tech shop would be glad to have your business. You might not need every tool for every procedure.
Make sure the PC is OFF and UNLUGGED and only touch the edges of the RAM sticks when removing and reseating them. my keyboard (not external) keeps messing up too. If the problem persists, see "Contacting Dell" in your Owner's Manual for instructions on obtaining technical assistance. If the problem persists, try one RAM module (if you have more than one) and then swap it with the other module until you find the culprit.
I don't see that on the list?? After a few seconds (2-8 seconds) both these lights go off. Jun 17, 2009 #6 B00kWyrm TechSpot Paladin Posts: 1,436 +37 In other Dell Systems, your beep code means...Click to expand... It turns on, it will have the DELL boot picture come on and I can access F2,F8,ANDF12.
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in your Owner's Manual. This beep code tells you that the computer encountered a memory problem. Connect with me on: Google+ 36 Comments mark harris July 7, 2010 I MOVED MY DAUGHTER OVER THE WEEKEND.HER COMPUTER WAS RUNNING FINE.SHE PUT IT IN THE TRUNK OF HER CAR.ONE Here is an example of the online documentation of a Dimension 4600.
Code Cause 1-1-2Microprocessor register failure 1-1-3NVRAM 1-1-4ROM BIOS checksum failure 1-2-1Programmable interval timer 1-2-2DMA initialization failure 1-2-3DMA page register read/write failure 3-1-1Slave DMA register failure 3-1-2Master DMA register failure 3-1-3Master interrupt Then I get a black screen than onl has "strike F1 to retry boot, F2 for setup utility". But my monitor still wont come on, it just gives me a black screen. so far this has taken me 15 mginutes to type because my cursor keeps jumping around & i am (here is an exampleno gt typin) typing in the wrong place.
Continue until you have identified a faulty module or reinstalled all modules without error. The manual should tell you all of the various codes. KB/Interface ErrorAn error occurred with the keyboard connector.Ensure that nothing is resting on the keyboard; if a key appears to be stuck, carefully pry it up. Prices ranged from $699 to $2000 depending upon user configuration.