Home > Canon Printer > Canon Printer Error 343

Canon Printer Error 343

Contents

Cause: Defective internal unit; (byte pack interrupt was not generated). Cause: Defective internal unit; (byte pack interrupt was not generated). Solution: Adjust the NL equalizer so the other party can receive the phase signal properly. ##551 [ TX / RX ] Voice IC malfunction. Cause: The other party released the line during transmission. Source

Solution: Adjust the NL equalizer so the other party can receive picture or MPS signals properly. Cause: The other party cannot receive NSC signals properly due to poor line conditions. Solution: Replace the modem or modem attached circuit board. Cause: Defective internal unit.

Canon Printer Error Code

A. Reset the ink detection waste ink pad capacity to 0, in the service mode. Solution: Refer to specific trouble shooting procedures in Service Manual. ##052 [TX / RX) Backup Memory damaged. Cause: The other party cannot receive properly due to poor line conditions.

Credentials confirmed by a Fortune 500 verification firm. Solution: Boost the transmission level so that the other party can receive the signals properly. A. Canon Printer Error Code 5011 Solution: Adjust the NL equalizer so the other party can receive picture or Q signals properly.

Solution: Boost the transmission level so the other party can receive picture or EOM signals properly. Canon Printer Error Code 5100 A. A. Solution: Adjust the NL equalizer so the other party can receive the phase signal properly. ##007 [ TX ] Failed CFR2 reception during G2 transmission.

Cause: Defective internal unit; (+24 volts down). Canon Printer Error Code 6000 Solution: Contact the telephone company. ##117 [ RX ] Receive DCN after DIS transmission from the second sheet. Solution: Record the protocol on DAT tape and then request the Canon Technical center to analyze the information. ##732 [ RX ] Receive RNR after picture reception. Cause: The operation of the UPI to control READ operations did not finish properly.

Canon Printer Error Code 5100

Cause: Defective internal unit. Solution: Have the other party boost the transmission level so this machine can receive the signals properly. Canon Printer Error Code Cause: The ink sensor is defective. Canon Printer Error Code B200 Cause: Defective internal unit; (LBP VSREQ does not go on).

Solution: Have the other party boost the transmission level to receive the picture signals properly. this contact form Cause: (After TCF transmission before picture signals); The other party cannot properly receive due to low transmission level. Cause: The CS motor does not run. Cause: The other party is out of recording paper. ##609 [ TX / RX ] Fail to detect end of other party's MF1 signal. Canon Printer Error Code 300

B. Administrative Connection Type Operating System Platform Products Pages: 67 - [ 1 2 3 4 5 … 67 | Next ] ID Title Views Posted ART166667 Link to UPS Tracking Reset the maintenance jet absorption pad capacity to 0, in the service mode. have a peek here Cause: Defective internal unit; (EEPROM write error).

characters left: Contact Us|Terms of Service|Privacy & Security|About Us|Our Network © 2003-2016 JustAnswer LLC JustAnswer UKJustAnswer GermanyJustAnswer SpanishJustAnswer Japan 125 10744821 Login|Contact Us Printers Printer Repair Questions? Canon Printer Error Code 5200 A. Solution: Lower the transmission start speed to 4800 bps.

A.

I tried and it worked.http://www.fixyourownprinter.com/forums/inkjet/29693 by Maria1 on Aug 19, 2007 at 6:25pm Add comment Please sign in to comment 0 Here is a link of a picture of the printer A. Cause: The document was not set during polling. Canon Printer Error Code U052 A.

A. Question about Xerox Printers & Copiers 1 Answer Error code 9 343 error code 9 343 Error code 9 343 - Xerox DocuColor 12 Printer Question about Xerox Printers & Copiers Solution: Replace the motor. Check This Out Ask DrKlahn Your Own Question DrKlahn, Engineer Category: Printers Satisfied Customers: 2152 Experience: BSci: Electrical Engr., Industrial Engr, and Computer Sci. 63151004 Type Your Printers Question Here...

Cause: Stop button was pressed during communication Solution: Retransmit ##286 [ TX ] DCN reception after EOM transmission. Let the machine sit for awhile so BJ head can cool down and retry. Solution: Power cycle the machine (unplug unit). Respond to this 0 You should look at the Canon MPC ink tank full thread..I'm pretty sure that's what your problem is and you are not alone.

Solution: No solution as modem speed is dependant on each machines specifications.